FJUMT-02 - Tandem Flange, square, mm - igus

CAD model selection

	1
	2
	3
	4
	5
	6
	7
	8
	9

		LINA Bill of material	ARTNR Part no. ⁿ/ₐ	NDM Dimension Nominal Diameter [mm]	TOL Tolerance Bearing Inner Diameter [mm]	FL Flange length FJUMT-01/02.. [mm]	PLF Effective surface area FJUMT-01/02.. [mm^2]	D1 Diameter [mm]	D2 Diameter [mm]	D3 Length [mm]	DT Length [mm]	K Width [mm]	B Length [mm]	BF Length [mm]	TS Length [mm]	DB Diameter [mm]	DS Diameter [mm]

		FJZMT-02-08	FJZMT-02-08	8	0.032 - 0.070	45	256	8	16	32	24	25	45	8	3.1	3.5	6.0
		FJUMT-02-10	FJUMT-02-10	10	0.030 - 0.088	52	250	10	19	39	29	30	52	9	4.1	4.5	7.5
		FJUMT-02-12	FJUMT-02-12	12	0.030 - 0.088	57	324	12	22	42	32	32	57	9	4.1	4.5	7.5
		FJUMT-02-16	FJUMT-02-16	16	0.030 - 0.088	70	464	16	26	46	36	35	70	9	4.1	4.5	7.5
		FJUMT-02-20	FJUMT-02-20	20	0.030 - 0.091	80	580	20	32	54	43	42	80	11	5.1	5.5	9.0
		FJUMT-02-25	FJUMT-02-25	25	0.030 - 0.091	112	975	25	40	62	51	50	112	11	5.1	5.5	9.0
		FJUMT-02-30	FJUMT-02-30	30	0.030 - 0.110	123	1470	30	47	76	62	60	123	14	6.1	6.6	11.0
		FJUMT-02-40	FJUMT-02-40	40	0.030 - 0.115	151	2360	40	62	98	80	75	151	18	8.1	9.0	14.0
		FJUMT-02-50	FJUMT-02-50	50	0.030 - 0.130	192	3450	50	75	112	94	88	192	18	8.1	9.0	14.0

Additional Information

Users who viewed this, were also interested in

FJUM-02 - Square Flange, mm

FJUM-02 - Square Flange, mmigus 12.09.2022

FJUMT-01 - Tandem Flange, Round, mm

FJUMT-01 - Tandem Flange, Round, mmigus 12.09.2022

RTA - Pillow Block, Tandem Design, closed, mm

RTA - Pillow Block, Tandem Design, closed, mmigus 12.09.2022

WAF - Shaft End Block, mm

WAF - Shaft End Block, mmigus 12.09.2022

iglidur® G - type S - metric sizes

iglidur® G - type S - metric sizesigus 08.11.2023

SLS - Lead screw support blocks

SLS - Lead screw support blocksigus 13.09.2022

WFRM - Trapezoidal Lead Screw Nuts

WFRM - Trapezoidal Lead Screw Nutsigus 13.09.2022

WAS - Shaft End Block, Narrow Design, mm

WAS - Shaft End Block, Narrow Design, mmigus 12.09.2022

JUM-11 - Liner, lower clearance, mm

JUM-11 - Liner, lower clearance, mmigus 20.07.2021

DryLin® E - Stepper Motors - NEMA34 - Stepper Motors

DryLin® E - Stepper Motors - NEMA34 - Stepper Motorsigus 12.09.2022

Tiewrap plates - Option 3: Clip-on tiewrap plates for opening or fixed crossbars

Tiewrap plates - Option 3: Clip-on tiewrap plates for opening or fixed cros...igus 19.01.2021

TAF - Shaft End Support, fixed, mm

TAF - Shaft End Support, fixed, mmigus 12.09.2022

iglidur® Q - type S - metric sizes

iglidur® Q - type S - metric sizesigus 19.01.2021

Single rail - Square

Single rail - Squareigus 09.09.2022